My New RDC6445G (EC) controller is installed and working but, when I power off and then power on (minutes , hours or days later) the settings revert back to default settings ie. x = 10000 mm / y = 10000 mm / z = 3000 mm .
I rewrite my actual settings for my machine 700 mm x 500 mm back via RDWORKS same issue .
I try with LightBurn write settings for 700 mm x 500 mm same issue ?
same result cannot get controller to retain settings written to it .
Howto get them to be retained ? HELP Please
6445G controller or user malfunction ?
-
Mark Elkins
- Posts: 17
- Joined: Wed Jul 17, 2019 9:32 am
- Location: columbus,in
- Country: United States
- Nickname: wanthamrd
- Laser Machine Make or Type: orion tech
- Laser Power: 60
- Laser Bed Size: 28 x 20
- Home Position: TL
- Control Software: RDWORKS
- RDWorks Version: 8.01.48
- Ruida Controller: RDC6445
- Windows Version: 10
-
Gene Uselman
- Posts: 2140
- Joined: Thu Jul 07, 2016 3:18 pm
- Location: Suburban Minneapolis, Minnesota, US
- Country: USA
- Nickname: Gene
- Laser Machine Make or Type: AKL1318-2
- Laser Power: 130W & 80W Reci
- Laser Bed Size: 51 x 71
- Home Position: TR
- Control Software: LIGHTBURN
- RDWorks Version: RDw .19 & Lightburn
- Ruida Controller: RDC6445
- Accessories: I have a combining lenses, pin tables [homebuilt], honeycomb tables , wireless remote, Modifed Ultimate Air Assist, home built non-powered rotary device, Prusa i3 MK3S and Mini Prusa printers.
- Windows Version: Win 10 Pro
Re: 6445G controller or user malfunction ?
The x + y will be 10000 til you home them to the homing switches.
If the Help and advice you received here was of VALUE...
Please consider making a donation to maintain the RDWORKSLAB Forum.
BT48 Alpha Shopbot and 1300x1800 130W Laser
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard
Please consider making a donation to maintain the RDWORKSLAB Forum.
BT48 Alpha Shopbot and 1300x1800 130W Laser
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard
-
Mark Elkins
- Posts: 17
- Joined: Wed Jul 17, 2019 9:32 am
- Location: columbus,in
- Country: United States
- Nickname: wanthamrd
- Laser Machine Make or Type: orion tech
- Laser Power: 60
- Laser Bed Size: 28 x 20
- Home Position: TL
- Control Software: RDWORKS
- RDWorks Version: 8.01.48
- Ruida Controller: RDC6445
- Windows Version: 10
Re: 6445G controller or user malfunction ?
tried that but every time the power is cycled I have to hit escape head crashes if i don't,
controller reverts back to 10000 x 10000 x3000 it is like starting all over with the wrong settings.
I've put rhe original 6442 controller back in and all is fine. , and yes I used the settings from the 6442 (manually entered)not firmware,with the 6445
and same issue. Controller Falure .
controller reverts back to 10000 x 10000 x3000 it is like starting all over with the wrong settings.
I've put rhe original 6442 controller back in and all is fine. , and yes I used the settings from the 6442 (manually entered)not firmware,with the 6445
and same issue. Controller Falure .
-
Chris Medcalf
- Posts: 40
- Joined: Sat Mar 30, 2019 10:04 am
- Location: UK
- Country: UK why is UK too short?
- Nickname: greenwing
- Laser Machine Make or Type: KH7050
- Laser Power: 60w ish
- Laser Bed Size: 700x500
- Home Position: TR
- RDWorks Version: new
- Windows Version: 7.01
Re: 6445G controller or user malfunction ?
The 10000mm x & y are positions, not dimensions. The controller doesn't know where the 0 position is for at least one axis, so it sets the x & y coordinates to 10000 so that you can use it without any chance of the coordinates going below 0.Mark Elkins wrote: ↑Wed Mar 15, 2023 4:59 pm tried that but every time the power is cycled I have to hit escape head crashes if i don't,
controller reverts back to 10000 x 10000 x3000 it is like starting all over with the wrong settings.
I've put rhe original 6442 controller back in and all is fine. , and yes I used the settings from the 6442 (manually entered)not firmware,with the 6445
and same issue. Controller Falure .
It seems the 6445 is not seeing a limit switch when the startup sequence happens, so the head crashes into the side. I think we can rule out the usual faulty wiring or switch problems, since the 6442 works.
Does the head travel towards the same corner at reset with both controllers?
-
Mark Elkins
- Posts: 17
- Joined: Wed Jul 17, 2019 9:32 am
- Location: columbus,in
- Country: United States
- Nickname: wanthamrd
- Laser Machine Make or Type: orion tech
- Laser Power: 60
- Laser Bed Size: 28 x 20
- Home Position: TL
- Control Software: RDWORKS
- RDWorks Version: 8.01.48
- Ruida Controller: RDC6445
- Windows Version: 10
Re: 6445G controller or user malfunction ?
All Limit Sensors are working .
reason being ,
I changed the controller & HMI back to the 6442
all connections are plug and play.
everything works .
reason being ,
I changed the controller & HMI back to the 6442
all connections are plug and play.
everything works .
-
Mark Elkins
- Posts: 17
- Joined: Wed Jul 17, 2019 9:32 am
- Location: columbus,in
- Country: United States
- Nickname: wanthamrd
- Laser Machine Make or Type: orion tech
- Laser Power: 60
- Laser Bed Size: 28 x 20
- Home Position: TL
- Control Software: RDWORKS
- RDWorks Version: 8.01.48
- Ruida Controller: RDC6445
- Windows Version: 10
Re: 6445G controller or user malfunction ?
Sorry,
yes ,
both do.
it's set to top left
yes ,
both do.
it's set to top left
-
Mark Elkins
- Posts: 17
- Joined: Wed Jul 17, 2019 9:32 am
- Location: columbus,in
- Country: United States
- Nickname: wanthamrd
- Laser Machine Make or Type: orion tech
- Laser Power: 60
- Laser Bed Size: 28 x 20
- Home Position: TL
- Control Software: RDWORKS
- RDWorks Version: 8.01.48
- Ruida Controller: RDC6445
- Windows Version: 10
Re: 6445G controller or user malfunction ?
I Did not and have not pushed the reset button on either controller .
just to be clear .
just to be clear .